Find the most up-to-date version of JIS G at Engineering JIS G Steel and steel products — General technical delivery requirements (Foreign Standard). Available for Subscriptions. Content Provider. Hi! I am finding JIS G , English version, who have this standrad. Pls, upload.
|Genre:||Health and Food|
|Published (Last):||4 June 2012|
|PDF File Size:||17.43 Mb|
|ePub File Size:||7.25 Mb|
|Price:||Free* [*Free Regsitration Required]|
However, JIS G Adds the specification item s or content s which are not included in International Standard. In the case where the width is less than 30 mm, however, the measurement shall be made at a mid-width position.
Test method shall be in accordance with Matters to be supphed by the purchaser are specified. I Hardness of the standard temper grade and as-annealed grade Hardness of the standard temper grade and as-annealed grade shall be in accordance with either An- nex 1 table 1 or Annex 1 table 2. JSA All rights reserved. Analytical test is specified.
The relevant Minister and the Japanese Industrial Standards Committee are not responsible for identifYing the patent right, application for a patent after opening to the public, utility model right or application for registration of utility model after opening to the public which have the said.
Steel and steel products – General technical delivery requirements. Aircraft and space vehicle engineering For steel sheet excluding cut lengths thereof One test piece each for tensile and bend tests shall jiw taken from each test lot of the same heat where the maximum thickness of the steel sheet is within twice the minimum thickness thereof.
The repair by welding shall not be performed. Wires Introduction This Japanese Industrial Standard has been prepared based on the second edition of ISO Steels for cold heading a11d cold extruding published in with some modifications of the technical contents.
Steel sheets and strips as rolled shall not be oiled. Judgment of the reinspection is specified. When it is infeasible, however, the sampling y0404 be made as close to the aforementioned position as possible. Carbon steels for cold heading — Part 2: Paint and colour industries Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic h0404 mechanical, including photocopying and microfilm, without permission in writing from the publisher.
For g04004 tensile test, t No.
JIS G (Outdated-currently )
The values specified in table 4 shall not jiz applied to the irregular portions of both ends of the steel strip. Our offices will be closed from December 24, to January 2, inclusive. In the case, the report shall be in accordance with the requirements of clause 13 in JIS G V Justification for the technical deviation and future measures Tensile strength, elongation and bendability are specified.
Company organization, management and quality. Over 4 to and inc!.
Modification of the tensile direction will cause the confusion in the marketo This is the unique configuration to JIS.
The theoretical mass shall generally be applied for the steel sheet mm or more in width during cold rolling, and the actual mass shall be applied for the steel sheet under mm in width during cold rolling. In JIS, provisions for hardness test, bend test and plastic strain ratio deter- mination are added.
The flatness specified shall apply only to the steel sheet of stan- dard temper grade which is mm or over in width during cold rolling. NOTE 1 The steel sheet and strip may be de scaled by pickling or shot blasting after the hot-rolling operation on request by the purchaser. The portions with continuous sidelines or dotted underlines are the matters in which the content of the corresponding International Standard has been modified.
Table 24 shall be applied as agreed between the purchaser and the supplier.
Wire rods JIS Z However, those of wires of 32 mm or over in wire diameter shall be as agreed upon between the purchaser and the supplier. Over 25 to and incl. Remarks 1 Flatness shall be measured by laying a steel sheet under its own mass on a flat surface plate, and the value of flatness shall be determined as the difference between the maximum deviation of convex from the flat surface and the nominal thickness of the steel sheet when its convex side is upper-most.
Alert me in case of modifications on this product contact us. Mass of single bundle gg0404 Mass of single sheet kg X number of sheets per bundle of same size Rounded off to integer in kg.
Construction materials and building Hardness not in table of ASTM, is calculated by interpolation.