EV CPS2.9 PDF

Designed for the contractor, the CPS MK II feature 2-RU chassis, Phoenix-type connectors for inputs and outputs, pre-programmable power-on delay, easy power-on via remote contact closures, rear panel attenuators, and a switchable 50 Hz high-pass filter. Like the CPS multi. Two-Channel Models CPS, CPS, CPS, and CPS CPS2.x rear view. Remote power-on contact. 1. Programmable power-on timer. 2. Module slot for. Buy Electro-Voice CPS 2-Channel Power Amplifier for RCM IRIS-Net Remote Control Module (W, 4 Ohms) Review Electro-Voice CPS

Author: Tara Moogugis
Country: Costa Rica
Language: English (Spanish)
Genre: Business
Published (Last): 19 February 2009
Pages: 221
PDF File Size: 13.16 Mb
ePub File Size: 6.32 Mb
ISBN: 650-5-11838-400-7
Downloads: 57267
Price: Free* [*Free Regsitration Required]
Uploader: Dagar

The difference between power consumption and dispensed power is called power dissipation P d. Whenever possible, using balanced audio signal feeds at the input of the power amplifier is always preferred.

Electro-Voice Cps MKII Contractor Class-h Power Amp 2x Watts | eBay

Turning the Mains Switch to ON starts booting up the power amp. The correct connection is also indicated at the amplifiers rear panel. This vps2.9 all protections are working fine. Unbalanced connections should only be used if the cables are very short and no interfering signals are to be expected in the vicinity of the power amplifier.

Electro-Voice CPS2.9 Manuals

Set the switch to the 50 Hz position for activating the High Pass Filter. Electrovoice compact precision cps: Show all Contractor precision cps2. As with all Electro-Voice power amps with fan cooling, the airflow direction is front-to-rear, obviously because there is more cold air outside of the rack case than inside.

Only the provided power cord may be used. Sv amount of heat resulting from power dissipation might remain inside of a rack-shelf and cpz2.9 to be diverted using appropriate measures. Do not use the power amplifier near heat sources, like heater blowers, stoves or any other heat radiating devices.

  FORMULATION OF LARGE VOLUME PARENTERALS PDF

This manual also for: In this case, bridging the screen shielding and the pin of the inverting input inside of the connector is mandatory. Introduction 1 Introduction 1. Csp2.9 DUAL mode, the two channels of the power amplifier work independent from each other.

Mounting CPS amplifiers have been designed for installation in a conventional inch rack case. Amplification is set via input level control of channel 1 only. Don’t have sv account? The audio signal has to be applied to the input connectors of channel 1.

Got it, continue to print. To print the manual completely, please, download it. A soft start circuit compensates mains inrush current peaks and thus prevents triggering AC mains fuse when switching on the amplifier.

Attach the power amp as shown in the illustration using 4 case nuts and screws. In general, setting up or mounting the power amplifier has to be done in a way that fresh air can enter unhindered at the front and exhausted air can exit at the rear.

Also See for CPS2.

The ground lift switch allows eliminating noise loops. Otherwise, a 6 dB drop in level could result. During installation, always separate eb power amplifier from the mains.

Level Indicators for channels 1 and 2 2. Additionally securing the amplifier at the rear becomes necessary, if the rack case in which the power amplifier has been installed will be transported.

  CANNOT EXECUTE COMMAND TEXNICCENTER PDF

Turning the control to eb right increases and turning it to the left decreases the volume. This mode of operation is being used for all 2-channel applications, like stereo operation. Make sure to completely read and fully observe power rating specifications of the speaker systems to be used and to check them against the output power capacity of fps2.9 power amp.

The power amplifier remains cooler and dissipating the developing waste heat in a specific direction gets easier. Connect the power amplifier only to a mains network, which corresponds to the requirements indicated on the type eg.

Electro-Voice CPS 2-Channel

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintance servicing instructions in the Controls, Indicators and Connections Front View 1. Mains Switch Rear View 1.

Following table shows possible switch settings and corresponding delay times. Electrovoice contractor precision cps2t: The audio signal has to be applied to the input connectors of channel 1, amplification is set via input level control of channel 1 only.

Unbalanced connections should only be used if the cables are very short and no interfering signals are to be expected in the vicinity of the power amplifier. Keep ventilation louvers free from dust to ensure unhindered airflow. Due to their immunity against external interference sources, such as dimmers, mains connections, HF-control lines, etc.

Do not modify this unit!