ASTM C1585 PDF

Documents Similar To Astm c ASTM C – Uploaded by. Alejandro Pinto. ASTM C Uploaded by. Nelson. BS EN Uploaded by. ASTM C Measurement of Rate of Absorption of Water by Hydraulic-Cement Concretes. Lab ID: Use This method is intended to determine the. caused by the deterioration mechanism by the means of the ASTM C C 04 results were then analyzed to validate the applicability of the.

Author: Juk Meztitaxe
Country: Kenya
Language: English (Spanish)
Genre: Sex
Published (Last): 13 June 2005
Pages: 483
PDF File Size: 8.24 Mb
ePub File Size: 1.61 Mb
ISBN: 814-2-67944-367-1
Downloads: 33099
Price: Free* [*Free Regsitration Required]
Uploader: Jujas

Instructions Provide at least two concrete cylinders or cores. The exterior surface is often subjected to less than intended curing and is exposed to the most potentially adverse conditions. Referenced Documents purchase d1585 The documents listed below are referenced within the subject standard but are not provided as part of the standard.

Water absorption is also strongly affected by the moisture condition of the concrete at the time of testing. The exterior surface is often subjected to less than intended curing and is exposed to qstm most potentially adverse conditions. In unsaturated concrete, the rate of ingress of water or other liquids is largely controlled by absorption wstm to capillary rise.

The exposed surface of the specimen is immersed in water and water ingress of unsaturated concrete is dominated by capillary suction during initial contact with water.

This test method is used to measure the water absorption rate of both the concrete surface and interior concrete. C585 Policy Sensors Sitemap. No other units of measurement are included in this standard.

  DIEGO DI MARCO ABC PARA REJUVENECER PDF

Print and complete the following order form. Historical C15885 s – view previous versions of standard. Order Form 2 Email complete form to contact listed below.

ASTM C Rate of Absorption of Water by Hydraulic Cement | CTLGroup

If you need more info or have any questions, please note the Lab ID number and contact us at:. The following information should be provided to be included in the report: It is c1558 responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. The test surfaces shall c158 at the same distance from the original exposed surface of the concrete.

The core is drilled vertically or horizontally. This test method is used to measure the water absorption rate of both the concrete surface and interior concrete. Test Method Con the other hand, is used to estimate the maximum amount of water that can be absorbed by a dry specimen and therefore provides a measure of the total, water permeable pore space.

Use This method is intended to determine the susceptibility of an unsaturated concrete to the penetration of water. In this test method, only one surface is exposed to water at room temperature while the other surfaces are sealed simulating water absorption in a member that is in contact with water on one side only. The specimen is conditioned in an environment at a standard relative humidity to induce a consistent moisture condition in the capillary pore system. The average of test results on at least 2 specimens shall constitute the test result.

  GAPO NI LUALHATI BAUTISTA PDF

In general, the rate of absorption of concrete at the surface differs from the rate of absorption of a sample taken from the interior. Link to Active This link will always route to the current Active version of the standard. If you need more info or have any questions, please note the Lab ID number and contact us at: By drilling a core and cutting it transversely at selected depths, the absorption can be evaluated at different distances from the exposed surface.

In general, the rate of absorption of concrete at the surface differs from the rate of absorption of a sample taken from the interior.

ASTM C1585 – 13

When cores are taken, they should be marked so that the surface to be tested relative to the original location in the structure is clearly indicated. The core is drilled vertically or horizontally. By drilling a core and cutting it transversely at selected depths, the absorption can be evaluated at different distances from the exposed surface. Time for Results Please contact a CTLGroup astn services representative zstm Project Manager to discuss your individual project needs and testing response times.

The surface to be exposed during testing shall not be marked or otherwise disturbed in such a manner as may modify the absorption rate of the specimen.