GHz FHSS-1 RX 6-Channel Full-Range Receiver Operating Instructions Use this receiver with your Airtronics RDS GHz transmitter or . We appreciate your purchase of this new AIRTRONICS. VG or VG Radio System. These instructions are intended to acquaint you with the many unique. Airtronics/Sanwa VG Modes? Radios. All; Planes; Sailplanes; Helis; FPV; Multirotors; Cars; Boats. About Sanwa VG Here you can.

Author: Akilabar Nibei
Country: Fiji
Language: English (Spanish)
Genre: Love
Published (Last): 14 August 2013
Pages: 415
PDF File Size: 18.65 Mb
ePub File Size: 12.16 Mb
ISBN: 824-6-93754-530-7
Downloads: 66730
Price: Free* [*Free Regsitration Required]
Uploader: Vishicage

It’s a community-based project which helps to repair anything.

Airtronics VG6000 (6 channel computer radio)

Cho, Ikoma-City, Nara, Japan. The Trainer system in the VG transmitter allows you to connect any two Airtronics RD series transmitters together for the purpose of training a new pilot. You will use two servos on two seprate channels to mix both ailerons and elevator together using only the left and right wing controls. The VG will not lose any memory even if you were to remove the main battery.

By pressing ‘print’ button you will print only current page.

The receiver is susceptible to vibration and moisture. All trims, mixes, servo directions, etc. To the manyal of our knowledge, these tests were performed using measurement procedures consistent with industry or Commission standards and demonstrate that the equipment complies with the appropriate standards.

Aircraft fuselages and helicopter frames may contain conductive components.

Alternatively, cut two short pieces of plastic tube and slide one antenna reception wire into each piece of tube, then tape or glue the tube to your model.


DO NOT operate your model again until you are certain the problem has been corrected. Always before use, conduct a bench test to ensure that the servos operate properly. The Bind LED on the receiver will continue to blink slowly. Page 22 Your battery is rated at 9. The tubes will protect the antenna reception akrtronics from damage. Add to my manuals Add. To the best of our knowledge, these tests were.

Under no circumstances should the antenna reception wires be mounted parallel to each other. Receiver Precautions l l l l l l vt6000 The receiver antenna wires consists of two coaxial cables and two reception wires the thin tip at the end of the coaxial cables. For more information, see page 3. Airtronics has invested a large amount of design effort to ensure that the powerful capabilities of the VG are as simple as possible to use.

After 3 minutes, the transmitter will revert to Normal mode. Page 9 NiCd airttonics pack and antenna. Page 3 Additional Receivers that will work with the VG The response speed of the receiver can be affected if used where multiple 2. The receiver should be wrapped in foam and the foam should be secured around the receiver to hold it in place. Don’t have an account?

Airtronics VG (6 channel computer radio) | #

We recommend that you bind the transmitter and receiver prior to mounting the receiver into your model. VG This equipment has been tested in accordance with the requirements contained in the appropriate Commission regulations. We further certify that the necessary measurements were. When installed in an electric-powered model, keep the receiver antenna wires as far away from the gv6000, battery, and electronic speed control ESC as possible.

  DG4S4 016C B 60 PDF

When the binding procedure is successful, the Bind LED on the receiver will stay solid blue when both the transmitter and receiver are turned ON.

Due to differences in the implementation of 2. On a fully charge battery, you may see the voltage as high as Make sure that the receiver, servo sand switch harness connectors are securely fitted.

Airtronics VG6000 Transmitter dual charger battery pack manual remote control

Page 20 All settings are saved automatically on all models. Unlike ordinary crystal-based systems, your model can be used without frequency control. Also, if response seems slow during use, discontinue use as quickly as possible.

Observe any applicable laws and regulations in place at your flying site when using the 2. To adjust stick length, hold Part B with your fingers and unscrew Part A counterclockwise to loosen the two pieces. The transmitter is now in Low Power Mode. The transmitter will stay in Low Power Mode for 3 minutes. Failure to mount the receiver antenna wires as described can result in poor reception, or in some cases, complete loss of reception.